Image Added

The Gigaset N870 SPK PRO (Site Planning Kit) DECT Site planning Kit helps you to plan and install your DECT multi-cell system. It contains one measuring base station, two measuring handsets and further helpful accessories for exact determination of the DECT environmental conditions for the planned network, and is delivered in a case. Image Removed

You can use the measuring devices in the case to determine the DECT wireless coverage at your location, establish how many base stations are required and their optimum location and find sources of interferences in the wireless network.

Additionally, you can use the equipment of the DECT Site Planning Kit (SPK) PRO to check the radio quality of problematic areas in an installed system and so eliminate network problems.

Stand

Image RemovedImage Added

To obtain an exact measurement, we recommend that you mount the measuring base station and battery carrier securely on a stand. The base carrier is fitted with a thread connection for this purpose. This enables you to simulate the installation of a base station at every possible height and check the layout and range of the network.

The stand should have a screw thread and be extendable to a height of 2.50 to 3.00 m.

Please note that the measuring devices run on batteries that must be charged before you start taking measurements. Bear this in mind when planning your time.

The Power-bank needs to be charged via the 30 W USB-C charger (fasted charging) or via the USB-A charger (Slower charging), the charging time is approximately ... hours.

You need two batteries for each measuring handset. These can be charged in the chargers and in standard charging devices. The charging time in the charger is approx. 8.5 hours.

To ensure freedom of movement when measuring and not be dependent on being able to reach a power connection, operate the measuring base station via the power-bank. The case contains a power-bank and a USB-C charger device for this purpose. 

The measuring handsets

• Are already registered to the measuring base station on delivery
• Calls between the handsets are possible using the number "1" and "2"

There are 2 measurements procedures supported:

• Advanced measurement procedure dialing ***922
• Display Simple metering mode
  
  

How to download the Measurement files

The measurement files can be downloaded via:

1. Download button in Web-interface (From software 2.54 or higher)
2. CLI 
   
   

Measurement files via CLI

cli@base-dm-7c2f80cfe206:~$ measure-dump -h
Usage: measure-dump [<options>]
-h        Show this help
-l        Lists all sites of which measurement logs are available
-r <site> Remove the generated measure-dump.tar file (/tmp/pub/measure-dump.tar)
          and the measurement logs of given site (dflt: all sites)
<site>    Dump measurement of given site, if option is not provided, all sites will be dumped

Note: Don't forget to remove your measurement data, if download was successful.
Otherwise you might leave your data on the measurement device.

cli@base-dm-int-7c2f80c6e48e:~$ measure-dump

These files can be download via:

• WINSCP
• via your browser, example: https://<IP address>/pub/measure-dump.tar
• other SSH tools ..

In the previous SPK, we used the metering mode to show the current status values of the connection to the base station.

It is possible to enable the metering mode. (Only supported by calibrated handsets)

Activating/deactivating metering mode

Press and hold the off key Image Removed to deactivate the handset

Press Image Removed, Image Removed and Image Removed at the same time and hold them down. Then press and hold the on key Image Removed

delete the Measurement files via the following handset procedure.

In the previous SPK, we used the metering mode to show the current status values of the connection to the base station.

In the new SPK, this metering mode is disabled and for this, the advanced measurement mode is introduced.

It is possible to enable the metering mode. (Only supported by calibrated handsets)

Activating/deactivating metering mode

• Press and hold the off key Image Added to deactivate the handset
• Press Image Added, Image Added and Image Added at the same time and hold them down. Then press and hold the on key Image Added
• The handset is now in Service mode
• Enter the five-digit service PIN. On delivery this is 76200
• The service menu is opened
  
  

Start   Press the display key to activate metering mode.

Back   Press the display key to exit the service menu again.

The handset is deactivated. When you reactivate it, it is in metering mode with the selected settings.

We support the following antenna mode options:

A50 = 50%mix of the two antennas for idle status quality measurement

Both antennas are used for 50% which acts the same like if a handset is in idle mode. This mode is recommended to check quality, because it is typically

• seen by handset in idle status,
• seen from base stations synchronizing via DECT.

Measurement done in this mode can provide a lower signal quality then using the Aopt mode but for a DECT measurement it is the better method.

• Therefore this is the default setting for Gigaset DECT SPK PRO. 

Aopt = In call optimized antenna

During an active call, the antenna optimization (diversity) is used. Where automatically the best antenna is selected by the system to offer the best speech quality.

This is the default setting for regular base stations of the Gigaset DECT PRO product family, to select best antenna in call state.

<?xml version="1.0" encoding="UTF-8"?>
<provisioning version="1.1" productID="e2">
    <nvm>
        <!--
        0x00 //current best antenna-diversity algorithm
        0x13 //Dummy-Bearer Algorithm ~50% per antenna
        -->

        <param name="

DmGlobal.

0.

DECTAntennaMode" value="

0x00" />
    </nvm>
</provisioning>

Do you have any questions?
For quick help and information, please refer to this user guide or visit our wiki: wiki.gigasetpro.com

For online information and services concerning

Here we describe how:

• You can create an DECT measurement base using an normal DECT base
• Restore DECT SPK base after factory reset

If you want to create your own DECT measurement base or restore the DECT SPK base after you have given it a factory reset you need to follow the following procedure:

• You can use an N870 / N870(E) or even an N670 device
• Upgrade your DECT system to software 2.53.0 or higher
• The R700H SPK handset must have software 12.02 or higher

• Download the provisioning file SPK_provisioning_template.xml
  The default IP address = 192.168.143.1 if you want to use your own IP address, you can change it in the template before uploading the provisioning file in your system.

  Expand
  title Click to see the provisioning file content
  Code Block <?xml version="1.0" encoding="UTF-8"?> <provisioning version="1.1" productID="e2"> <nvm> <param name="network.lan.ipaddr" value="192.168.143.1" /> <param name="network.lan.netmask" value="255.255.0.0" /> </oper> <!-- Provider settings to make internal calls between the DECT handsets --> <param name="SipProvider.0.Name" value="Localhost"/> <param name="SipProvider.0.Domain" value="Localhost"/> <param name="SipProvider.0.ProxyServerAddress" value="127.0.0.1"/> <param name="SipProvider.0.TransportProtocol" value="2"/> <param name="SipProvider.0.CallsWhileUnregistered" value="y"/> <!-- Handset 1 with number 1 --> <param name="DmGlobal.0.SystemRegDomain" value="EUR" /> <oper name="addset_hs" value="00000"uci"> <param name="hs.RegStatus" value="ToReg"/> <!-- Change network to Static IP --> </oper> <param name="SipAccountnetwork.00000lan.AuthNameproto" value="1static" /> <param name="SipAccountnetwork.00000lan.AuthPasswordipaddr" value="GigasetSPK1192.168.143.1" /> <param name="SipAccountnetwork.00000lan.UserNamenetmask" value="1255.255.0.0" /> <param name="SipAccount.00000.DisplayName" value="1" /> </oper> <param name="SipAccount.00000.ProviderId" value="0" /> <!-- Provider settings to make internal calls <!-- Handset 2 with number 2between the DECT handsets --> <oper<param name="add_hsSipProvider.0.Name" value="00001Localhost"/> <param name="hsSipProvider.0.RegStatusDomain" value="ToRegLocalhost"/> </oper> <param name="SipAccountSipProvider.000010.AuthNameProxyServerAddress" value="2" 127.0.0.1"/> <param name="SipAccountSipProvider.000010.AuthPasswordTransportProtocol" value="GigasetSPK22" /> <param name="SipAccountSipProvider.000010.UserNameCallsWhileUnregistered" value="2y" /> <!-- Handset <param name="SipAccount.00001.DisplayName" value="2" /1 with number 1 --> <param<oper name="SipAccount.00001.ProviderIdadd_hs" value="000000" /> <param name="hs.RegStatus" value="ToReg"/> <!-- Enable that device starts with no LAN connected -->/oper> <oper<param name="SipAccount.00000.AuthName" value="set_uci1" /> <param name="networkSipAccount.lan00000.force_linkAuthPassword" value="1GigasetSPK1" /> <param name="networkSipAccount.lan600000.ifnameUserName" value="lo1" /> </oper> <param name="SipAccount.00000.DisplayName" value="1" /> <param name="SipAccount.00000.ProviderId" value="0" /> <!-- OpenHandset registration2 windowwith fornumber 36002 seconds --> <oper name="updateadd_dmhs" value="local00001" > <param name="RegStarths.RegStatus" value="1ToReg" /> </oper> <param name="RegDuration"SipAccount.00001.AuthName" value="2" /> <param name="SipAccount.00001.AuthPassword" value="3600GigasetSPK2" /> <param name="SipAccount.00001.UserName" value="2" </oper>> </nvm> </provisioning>

• Open the web-interface of your DECT system, go to: SETTINGS - System - Provisioning and configuration - Browse:
• Select the provisioning file and click on "Upload" and then "Start auto configuration"
• Wait until Left LED is Blue and Right LED is Green
• Register the 2 calibrated measurement DECT handsets PIN = 0000
• Power N870 without LAN and check if calls between handsets are possible
  Handset 1, number is "1"
  Handset 2, number is "2"

The SPK DECT base has the following default settings:

Via auto-provisioning

If you want to change the default static IP address 192.168.143.1 to your own preference, you need to follow the following procedure.

• Download the provisioning file on this page
• Change the IP address in this provisioning file to your own preference
• Upload the provisioning file and start provisioning
  
  

Via the web-interface

Image Added

Open the web-interface and go to:

SETTINGS - Network - IP/LAN and change the IP address

• DECT base: Via the web-interface you can upgrade the SPK base with an actual firmware: Firmware N870(E)/N670/N610
• SPK handset: Via Quicksync or SOUTA you can upgrade the SPK handset with an actual firmware: Firmware SL800H / S700H / R700H PRO