Versions Compared

Old Version 13

changes.mady.by.user Baremans, Eric

Saved on

compared with

New Version 14

changes.mady.by.user Baremans, Eric

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Section
Panel
titleColor#F85404
titleBGColor#F0F0F0
titleIntroduction

The N870 has only one hardware.

When you connect an N870 to the Power, it will start by default as a base station. You can change the role of the device using the procedure described on this page.

Panel
titleColor#F85404
titleBGColor#F0F0F0
titlePreparation
  1. Perform DECT measurement and site planning
    During the planning phase of your DECT network you should have created an installation plan for the DECT managers and base stations.
  2. Connect the devices to the local network.
  3. Register at least one device as Integrator/DECT manager.
  4. Mount the devices at the planned locations.
  5. Configure the local network settings via web configurator.
    You need a PC connected to the local network, so that you can configure your telephone system via web configurator.
  6. Perform a firmware update.
  7. Register the base stations to the telephone system.
  8. Configure the base station synchronization.
  9. Configure VoIP PABX or provider.
  10. Register handsets and perform handset configuration.
  11. Create a backup to save your configuration
Panel
titleColor#F85404
titleBGColor#F0F0F0
titleHow to change the role.

Per default, the device is delivered as a base station.

To change the role to a Integrator/DECT Manager or to reset the base, please follow this instruction.

  • To activate the programming mode, press and hold the hardkey for minimum 10 seconds.
  • After 10 seconds, the LED's will be switched off and the device is in the programming mode.
  • In programming mode you can step through the three options by single key presses.
  • The modes are indicated by the LEDs.
  • To activate the intended option: Press and hold the hardkey for 5 seconds (minimum 3 up to maximum 10 seconds).
  • The programming mode is closed after 20 sec of no activity.

Remark: Please be aware that existing configuration and user data will be lost. Please perform backup in advance if needed

Example: How to change the role to: Integrator/Manager and DECT base in one
  1. Press hard key key for 10 seconds, until LED's are switched off.
  2. Green LED will be On and role is DECT Base.
  3. Press key and both LED's will be Blue. Role will be: Integrator/DECT Manager and Base. (All in One)
  4. Press key for 5 seconds to confirm the new role.
  5. Device will reboot and will come online as Integrator/DECT Manager and Base, with factory default settings.

Info: Reboot can take up to 5 minutes !!!

After reboot the LED's will show different colors then when changing the role.

Panel
titleColor#F85404
titleBGColor#F0F0F0
titleProgramming mode

Progr.
option

Role

IP

Description

LED 1

LED 2

activate by

0

Programming modeoffoffpress & hold key for
around 10 seconds. (LED's turn off)
The device will show direct the role Base station when entering the programming mode.
1
  • Base station
DHCPSet role to Base (default).
Greenpress & hold key for 5 seconds
With one key press you switch to the next option. (All in one)
2
  • Base station
  • Manager
  • Integrator
DHCP
IP address obtained automatically 		Set role to Base + DECT Manager + Integrator.BlueBluepress & hold key for 5 seconds
With one key press you switch to the next option. (All in one)
3
  • Base station
  • Manager
  • Integrator

Static IP: 192.168.143.1

Subnet mask: 255.255.0.0

Set role to Base + DECT Manager + Integrator and apply static IP address.
Bluepress & hold key for 5 seconds
With one key press you switch to the next option.
4
  • Base station
  • Manager 
DHCPSet role to Base + DECT ManagerBlueGreenpress & hold key for 5 seconds
With one key press you switch back to the beginning, the Base station role
Info
titleImportant

After the above procedure, the device will be factory default and all of your settings will be removed.