Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Section
Panel
bgColor#FDFEFE
titleBGColor#CACFD2
titleAlcatel Lucent OmniPCX Office / OXO Connect with IBS DECT base.
Column
width30%

About OXO Connect

Tested: OXO Connect R20

The system can handle up to 120 handsets.

The tested DECT system is the system using the IBS (Intelligent base Station).

Also available is the IP-DECT system where test results can be found here.

Column
width70%

See below for a list with tested features when registering a Gigaset pro handset to the Alcatel OXO Connect cordless system.

When you register a Gigaset pro handset to the Alcatel OXO Connect, the administrator has to add the handset manually via the Alcatel administrator OMC-tool. The administrator can select the GAP or GAP enhanced feature set. When using GAP enhanced, the platform will send more display information to the handset. In the list below you can see the difference between the 2 modes.

This test is done using the software versions that are reported on this page, we have no influence on the Alcatel software development. If the platform changes the software and the feature set of the DECT GAP support then it can be that additional or less functionality is possible.

DECT GAP protocol is a DECT standard and has a limited feature set, this causes that some functionality is not possible.

 

FeatureSL750HS650HR650HComment
Software636311 
DECT RegistrationYesYesYesStart the GAP registration mode on the OXO Connect using the OMC-tool. During our test, we used the PIN "0000". Start the registration procedure on the Gigaset DECT handset and enter the PIN "0000" if requested. The Administrator can decide during the Registration procedure to chose for the GAP or GAP enhanced mode.
Outgoing CallYesYesYes

GAP enhanced mode: On the handset display you can see the information provided by the platform, like name/number and call status.

GAP mode: Normal Gigaset display information, called number.

IVR / VM (DTMF)YesYesYes

With the settings below, the handset has to switch to DTMF using the using the right option button.
The handset can operate the IVR and Voicemail using the DTMF tones.

Incoming CallYesYesYes

External incoming calls shows the CLIP (Number) of the caller without the leading "0" for outgoing calls. In the Call lists, the numbers are stored with leading "0" so that call back is possible.

GAP enhanced mode: Shows CLIP information from PBX, local phone-book is not used to replaced number with name.

GAP mode: Show CLIP information and number is replaced with name if available in local phone-book.

Missed CallsYesYesYesMissed calls are signaled with icon in screen and MWI key is blinking. Because of GAP protocol limitation, the missed calls is a feature of the handset and not signaled by the platform.
Call Waiting answerPlatform featurePlatform featurePlatform feature

The 2e incoming call is signaled via Call-waiting tone. To answer the incoming call you can use the green button.

To swap between the calls, you need to use the feature code "3".

Call Waiting rejectNoNoNo 
Call HoldYesYesYes

Call hold can be done in 3 ways.

  1. Just press a key and other side will be put on hold, after .. time a recall will happen.
  2. Press Feature code "*1" and you will hear tone in handset, press "*1" again to retrieve the call.
  3. Mute handset microphone.
Attended transferYesYesYes

During the call, just enter the number of the person you would like to transfer to. The caller is put on-hold and other side is ringing. When answered just end call to transfer or swap between calls using feature code "3"

GAP enhanced mode: Display information on handset is updated when call transfer is done.

GAP mode: Display is not updated.

Unattended transferYesYesYes

During the call, just enter the number of the person you would like to transfer to. The caller is put on-hold and other side is ringing. End the call to transfer.

GAP enhanced mode: Display information on handset is updated when call transfer is done.

GAP mode: Display is not updated.

ConferenceYesYesYesConference can be started when having one active call and one call on-hold and pressing the feature code "4"
MWINoNoNo 
Date and TimeNoNoNoDue to DECT GAP protocol limitation, the handset can not receive the data and time automatically from the platform. The user has to enter the date and time manually on the handset. When the handset is turned off/on, the date and time has to be entered manually again.
Call listYesYesYesThe Call lists are handled by the dect handset and not synchronized with the platform, the DECT GAP standard does not support call list synchronization. Supported are All / Outgoing / Missed / Accepted call list.
Int keyNoNoNoWhen pressing the "int" key, the handset will give a dial-tone and you can dial a number. The internal user list will not be provided, this is not supported by the GAP standard.
PhonebookYesYesYes

It is possible to use the handset phonebook, there is no possibility to access the PBX phonebook.

GAP enhanced mode: Shows CLIP information from PBX, local phone-book is not used to replaced number with name.

GAP mode: Show CLIP information and number is replaced with name if available in local phone-book.

Handset featuresYesYesYesDependent on the used handset, you can use the remaining handset features like: Alarm clock / Bluetooth / Audio settings / Organizer / ....
Handover / roamingYesYesYesBased on customer feedback, the gigaset handsets are working perfect behind the Alcatel Lucent OXO Connect.

 

Alcatel-Lucent OmniPCX Settings.

The following DECT settings are used during our test.

 

 

Note: For Call Transfer you need to enable the Transfer by on hook Option at System miscellaneous -> Feature Design ->Part 2

Image Added