Provider and PBX profilesYou can use up to ten different VoIP PBX (Telephony Server) or VoIP provider profiles. In the web-interface go to: → Settings → Provider or PBX profiles The page lists the available VoIP connections. Name:
Domain:
Configuring provider and/or PBX profilesClick on On this page you can edit the data for the selected telephony server profile. Enter a name for the provider or PBX profile. This name is shown in the Provider/PBX list. To distinguish between different connections it should specify the respective VoIP service provider. Examples: sip.domain.net for john.smith@sip.domain.net 10.100.0.45 for 02871913000@10.100.0.45 Proxy server addressThe SIP proxy is your VoIP provider's gateway server and the first SIP server, where the device should send SIP requests and expects to receive requests.
Examples: 10.100.0.45 or sip.domain.net or sipproxy01.domain.net Proxy server port
Range: 1-65535; Default: 5060 (for UDP/TCP), 5061 (for TLS) DNS SRV SIP server redundancy lookup might provide a different server port which is used then. Registration serverThe registration server assigns the public IP address/port number that was used by the phone on registration to your SIP address (username@domain). With most VoIP providers, the registrar server is identical to the SIP server. But it is also possible to address another service for registrationof this account.
Examples: 10.100.0.45 or sip.domain.net or sipproxy01.domain.net Registration server port
Range: 1-65535; Default: 5060 (for UDP/TCP), 5061 (for TLS) Registration refresh time
Values: 1 - 5 digits, > 0; Default: 180 seconds Transport protocol
UDP:(User Datagram Protocol) UDP is a non session-based protocol. UDP does not establish a fixed connection. The data packets ("datagrams") are sent as a broadcast. The recipient is solely responsible for making sure the data is received. The sender is not notified about whether it is received or not. TCP:(Transmission Control Protocol) TCP is a session-based transmission protocol. It sets up, monitors and terminates a connection between sender and recipient for transporting TLS:(Transport Layer Security) TLS is a protocol for encrypting data transmissions on the Internet.TLS is a superordinate transport protocol. Use SIP Security (SIPS)Only if TLS is selected. SIPS enhances SIP with TLS/SSL encryption. Using SIPS makes it more difficult to listen in on the connection. Data is transmitted encrypted over the internet.
SRTP optionsOnly available if TLS is selected. SRTP (Secure Realtime Protocol) is a security profile to ensure confidentiality, integrity, replay protection and message authentication for audio-visual data transmission over IP-based networks.
Secure Real Time Protocol Security is activated for voice connections. Deregister detached HSThe SIP account of handsets that are not reachable can be de-registered automatically.
Redundancy settingsRedundancy - DNS queryVoIP providers provide SIP server redundancy for load balancing and service reliability. SIP servers can be identified by DNS using different queries: A Records just the specified IP addresses and the related port numbers. SRV + A Finds an available server port for the specified proxy and registration server. DNS SRV allows a client to only have to know what type of service it is looking for instead of the actual server. Failover serverIf Redundancy - DNS query = A In case your provider supports a failover server you can enter the data here.
Registration server
SIP server port
Range: 1-65535; Default: 5060 (for UDP/TCP), 5061 (for TLS) Network data of the service providerOutbound proxy modeThe DECT IP multicell system allows you to configure an outbound proxy. Despite of any other SIP protocol rules, if activated (Always), the system will always send all outgoing requests towards this outbound proxy. It can be an outbound proxy in the local network provided by the local network provider or in the public network provided by the network/VoIP provider.
Always: All signalling and voice data sent by the system is sent to the outbound proxy. Never: The outbound proxy is not used. If the further outbound proxy configuration is identical to the proxy and registrar configuration it is useless and will be ignored
Outbound server addressThis is the address, where the device should send all SIP requests to and where (in case of successful registration) it expects to receive requests from.
Example: 10.100.0.45 or sip.domain.net or sipproxy01.domain.net. If the Outbound server address field is empty, the system behaves independently of the selected mode, as with Outbound proxy mode = Never. Outbound proxy portThis is the port number of the outbound proxy server, where the device should send all SIP requests to (and where it in case of successful registration expects to receive requests from)
Range: 1-65535; Default: 5060 (for UDP/TCP), 5061 (for TLS) Outbound proxy port is empty and Outbound server address is a name: The RFC3263 rules will be used to locate SIP servers and select them for load balancing and redundancy. Outbound proxy port is a fixed number: The usage of DNS SRV records according to RFC3263 is blocked. SIP SUBSCRIBE for Net-AM MWIWhen activated a subscription is established for the purpose of receiving notifications about new messages on the network mailbox.
DTMF over VoIP ConnectionsDTMF signalling (Dual Tone Multi Frequency) is required, for example, for querying and controlling certain network mailboxes via digit codes, for controlling of automatic directory enquiries or for remote operation of the local answering machine. To send DTMF signals via VoIP, you must define how key codes should be converted into and sent as DTMF signals: as audible information via the speech channel or as a "SIP Info" message. Ask your VoIP provider which type of DTMF transmission it supports. Automatic negotiation of DTMF transmission
Send settings of DTMF transmission
Audio or RFC 2833 DTMF signals are to be transmitted acoustically (in voice packets). SIP Info DTMF signals are to be transmitted as code. Settings for codecsThe voice quality of VoIP calls is mainly determined by the codec used for the transmission and the available bandwidth of your network connection. A "better" codec (better voice quality) means more data needs to be transferred, i.e. it requires a network connection with a larger bandwidth. You can change the voice quality by selecting the voice codecs your phone is to use, and specifying the order in which the codecs are to be suggested when a VoIP connection is established. Default settings for the codecs used are stored in your phone; one setting optimised for low bandwidths and one for high bandwidths. Active codecs / Available codecs |
Selection of codecs G.722 and G.729 influence the system capacity in direction to lower amount of parallel calls per base station. Number of parallel calls per base station depending on Codec / Bandwidth:
|
Length of time in milliseconds represented by the audio data in one packet.
Call hold means that a user request to put an active call on hold. The holding part sends a re-INVITE request to the held client with an SDP offer (Session Description Protocol). This SDP offer contains the attribute line a=inactive or a=sendonly.
Inactive: The SIP endpoint would neither send nor receive data.
Sendonly: The SIP endpoint would only send and not receive data.
Define how call transfer can be performed:
Attended Transfer The first call on the phone's VoIP connection must be held until the consultation call is accepted. Only then can two callers be connected with each other.
Unattended Transfer The caller must only be placed on hold until the user have started the consultation call (dialled the number). The user can transfer the call before the second participant registers.
From the Calling Party (User Part) option menu select which information is allowed to be transferred to the receiving part within the SIP header. Which information is actually transferred is determined by the provider.
Only the FROM information can be added.
Caller identity in the form number@server, e.g.:12345678@192.168.15.1
P-Preferred-Identity (PPI) or FROM can be added
The P-Preferred-Identity header field is used from a user agent to a trusted proxy to carry the identity the user sending the SIP message wishes to be used for the P-Asserted- Header field value that the trusted element will insert.
P-Asserted-Identity (PAI) or PPI or FROM can be added.
The P-Asserted-Identity header field is used among trusted SIP entities (typically intermediaries) to carry the identity of the user sending a SIPmessage as it was verified by authentication.
Service codes are key sequences provided by the provider or PBX in order to activate/deactivate specific functions on the handset. You can set the adequate service codes for activating/deactivating CCBS and CCNR.
CCBS (Completion of Call to busy Subscriber) Ringback if busy
CCNR (Completion of Calls on No Reply) Ringback if no answer
In the text fields Call Completion on (CCBS, CCNR)/Call Completion off (CCBS, CCNR) enter the key sequence for activating/deactivating CCBS and CCNR.