N510 XML provisioning parameters

WebUI: Settings - IP configuration - IP address type

Enable/disable to obtain address from a DHCP server.

IPv4 address in hexadecimal format.

Example: 192.168.2.2-> 0xC0A80202 192(C0)168(A8)2(02)2(02)

WebUI:Settings - IP configuration - IP address

Enter an IPv4 address of your basestation. This IP address allows your phone to be reached by other subscribers to your local network (e.g., PC). 192.168.2.2 is the default. The IP address must be from the address block reserved for private use on the router. This is generally in the range 192.168.0.1 - 192.168.255.254 with Subnet mask 255.255.255.0. The subnet mask determines that the first three parts of the IP address must be identical for all subscribers in your LAN. The static IP address must not belong to the address block (IP pool range) that is reserved for the router's DHCP server. It must also not be used by another device on the router. If necessary, check the settings on the router.

IPv4 address in hexadecimal format.

Example: 255.255.255.0-> 0xFFFFFF00 255(FF)255(FF)255(FF)0(00)

WebUI:Settings - IP configuration - Subnet mask

For addresses from the address block from 192.168.0.1 to 192.168.255.254, the subnet mask 255.255.255.0 is generally used. This is the default setting.

IPv4 address in hexadecimal format.

Example: 192.168.2.1-> 0xC0A80201 192(C0)168(A8)2(02)1(01)

WebUI:Settings - IP configuration - Default gateway

This is generally the local (private) IP address for your router (e.g., 192.168.2.1). Your phone requires this information to be able to access the Internet. 192.168.2.1 is the default setting. Required is hexadecimal format 0xC0A80201.

IPv4 address in hexadecimal format.

Example: 192.168.2.253-> 0xC0A802FD 192(C0)168(A8)2(02)253(FD)

WebUI:Settings - IP configuration - Preferred DNS server

The DNS server is required to convert the DNS name into the IP address when a connection is being established to a server.

IPv4 address in hexadecimal format.

Example: 192.168.2.1-> 0xC0A802FE 192(C0)168(A8)2(02)254(FE)

WebUI:Settings - IP configuration - Alternate DNS server

Alternate DNS server should be used in situations where the preferred DNS server cannot be reached.

WebUI:Settings - IP configuration - Allow access from other networks

Select 'Yes' to authorise access from other networks. To disable remote access, select 'No' - access is then limited to PCs in your own local network.

WebUI:Settings - IP configuration - Device Name in the Network

Device Name in the Network field - maximum 20 characters (0-9,a-z,A-Z,-). The phone can be addressed with this name within the local network.

WebUI:Settings - IP configuration - Enable proxy

Select 'Yes' if your phone is to handle HTTP calls via your network's HTTP proxy server. If you select 'No', the phone will attempt to access the Internet directly.

WebUI:Settings - IP configuration - Proxy server address

Enter the URL of the proxy server to which your phone is to send HTTP calls. The proxy server then creates the connection to the Internet.

WebUI:Settings - IP configuration - Proxy server port

Enter the communication port used on the HTTP proxy server (number between 1 and 55000). It is mainly port 80 that is used.

WebUI:Settings - IP configuration - Use VLAN Tagging

Enable/disable VLAN tagging.

WebUI:Settings - IP configuration - VLAN Priority

Enter the VLAN Identifier. Numbers ranging from 0 to 4094 (12-bit values) are permitted.

WebUI:Settings - IP configuration - VLAN Identifier

Enter the VLAN Priority. Numbers ranging from 0 to 7 (3-bit values) are permitted.

WebUI:Settings - Telephony - Connections - Edit(button) - Connection Name or Number

Enter a name for the IP account. The default is: Account0->IP1 Account1->IP2 Account5->IP6

WebUI:Settings - Telephony - Connections - Edit(button) - Authentication name

Specify the authentication name agreed with your VoIP provider. The authentication name acts as access ID when registering with the SIP proxy/registrar server.

WebUI:Settings - Telephony - Connections - Edit(button) - Authentication password

Enter the password that you have agreed with your VoIP provider. The phone needs the password when registering with the SIP proxy/registrar server.

WebUI:Settings - Telephony - Connections - Edit(button) - Username

Enter the caller ID for your VoIP provider account (maximum 32 characters). The ID is usually identical to the phone number for this VoIP account.

WebUI:Settings - Telephony - Connections - Edit(button) - Display name

Enter any name that should be shown on the other caller's display when you call them. All characters in the UTF8 character set (Unicode) are permitted.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - Domain

Specify the last part of your SIP address (URI) here. Example: For the SIP address '987654321@provider.com', enter 'provider.com' under Domain.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - Proxy server address

The SIP proxy is your VoIP provider's gateway server. Enter the IP address or the (fully qualified) DNS name of your SIP proxy server. Example: myprovider.com.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - Proxy server port

Enter the number of the communication port that the SIP proxy uses to send and receive signalling data (SIP port).|Port 5060 is used bymost VoIP providers.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - Registration server

Enter the (fully qualified) DNS name or the IP address of the registrar server. The registrar is needed when the phone is registered. It assigns the public IP address/port number that was used by the phone on registration to your SIP address|(Username@Domain).With most VoIP providers, the registrar server is identical to the SIP server. Example: reg.myprovider.com.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - Registration server port

Enter the communication port used on the registrar. Port 5060 is used in most cases.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - Registration refresh time

Enter the time intervals (in seconds) at which the phone should repeat the registration with the VoIP server (SIP proxy) (a request will be sent to establish a session). The registration is repeated so that the phone's entry in the SIP proxy tables is retained and the phone can therefore be reached. The registration will be repeated for all enabled VoIP connections.The default is 180 seconds.If you enter 0 seconds, the registration will not be repeated periodically.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - STUN enabled

Select 'Yes' if you want your phone to use STUN. STUN can only be used if your router uses an asymmetric NAT and a non-blocking firewall.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - STUN server address

Enter the (fully qualified) DNS name or the IP address of the STUN server on the Internet (maximum 74 characters, 0-9,a-z,A-Z,-,.,_). The phone can determine its public address via the STUN. The phone needs this address in order to receive caller voice data.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - STUN server port

Enter the number of the communication port on the STUN server. The default port is 3478.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - STUN refresh time

Enter the time intervals at which the phone should repeat the registration with the STUN server. The registration must be repeated so that the entry of the phone in the STUN server tables is retained. The registration will be repeated for all enabled VoIP connections. The default is 240 seconds. |If you enter 0 seconds, the registration will not be repeated periodically.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - NAT refresh time

Specify the intervals at which you want the phone to update its entry in the NAT routing table. Specify an interval in seconds that is a little shorter than the NAT session timeout.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - Outbound proxy mode

Specify when the outbound proxy should be used. Always, all signalling and voice data sent by the phone is sent to the outbound proxy. Automatic, data sent by the phone is only sent to the outbound proxy when the phone is connected to a router with symmetric NAT or a blocking firewall. If the phone is behind an asymmetric NAT, the STUN server is used. Never, the outbound proxy is not used.

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - Outbound server address

Enter the (fully qualified) DNS name or the IP address of your provider's outbound proxy (maximum 74 characters, 0-9,a-z,A-Z,-,.,_).

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - Outbound proxy port

Enter the number of the communication port used by the outbound proxy. The default port is 5060.

BS_IP_Data1.ucI_SIP_PREFERRED_TRANSPORT_LAYER_N (N=2-6)

WebUI:Settings - Telephony - Connections - Edit(button) - Show Advanced Settings(button) - Select Network Protocol

The SIP server normally communicates via UDP (User Datagram Protocol). UDP does not guarantee reliable transmission, i.e. the SIP server does not check whether messages have been successfully transferred. If you need reliable transmission, you can also use TCP (Transmission Control Protocol). Automatic - the protocol is defined automatically. UDP only - communication occurs exclusively via UDP. TCP only - communication occurs exclusively via TCP.

Usage:

Account1: BS_IP_Data1.ucI_SIP_PREFERRED_TRANSPORT_LAYER

Account2: BS_IP_Data1.ucI_SIP_PREFERRED_TRANSPORT_LAYER_2

Account6: BS_IP_Data1.ucI_SIP_PREFERRED_TRANSPORT_LAYER_6

WebUI:Settings - Telephony - Audio - Allow 1 VoIP call only

You can usually make two VoIP calls at the same time on your phone. If, however, your DSL connection only has a low bandwidth, there may be problems if multiple VoIP calls are made at the same time. The data is no longer transmitted properly (long voice delay, data losses etc.). Select 'Yes' after Allow 1 VoIP call only to prevent any further parallel VoIP phone connections being established.

integer:

0=Own Codec preference

1=Opimized for high bandwidth

2=Opimized for low bandwidth

WebUI:Settings - Telephony - Audio - Voice Quality

Default settings for the codecs are stored in your phone: one setting optimised for low bandwidths and one for high bandwidths. Enable either 'Optimized for low bandwidth' or 'Optimized for high bandwidth' if you wish to apply a default setting for all VoIP connections. The settings are shown in the Settings for individual VoIP connections area and cannot be changed. Enable the 'Own Codec preference' option if you wish to select and set connection-specific voice codecs yourself.

integer:

0=Normal

1=High

255=Low

WebUI:Settings - Telephony - Audio - Advanced Settings - Volume for this VoIP account

Specify whether the incoming volume range is too high or too low. The following options are available: Low, handsfree/earpiece volume is too high. Enable this option to reduce the volume by 6 dB. Normal, the handsfree/earpiece volume does not need to be raised/lowered. High, handsfree/earpiece volume is too low. Enable this option to increase the volume by 6 dB.

Comma separated list of 5 elements:

0=PCMA G.711 u law

1=PCMA G.711 a law

2=G726

3=G729

5=G722

255=none

WebUI:Settings - Telephony - Audio - Advanced Settings - Available codecs

In the Available codecs lists, you can define your own codec preference tailored to your DSL connection. Select the voice codecs your phone is to use, and specify the order in which the codecs are to be suggested when a VoIP connection is established. Examples: G.711ulaw: '0,255,255,255,255' G.711ulaw,G.711alaw: '0,1,255,255,255' G.711ulaw,G.711alaw,G.726: '0,1,2,255,255' G.711ulaw,G.711alaw,G.726,G.729: '0,1,2,3,255' G.711ulaw,G.711alaw,G.726,G.729,G.722: '0,1,2,3,5'

Comma separated list of 5 elements:

0=PCMA G.711 u law

1=PCMA G.711 a law

2=G726 3=G729

5=G722

255=none

WebUI:Settings - Telephony - Audio - Advanced Settings - Selected codecs

In the Selected codecs lists, you can define your own codec preference tailored to your DSL connection. Select the voice codecs your phone is to use, and specify the order in which the codecs are to be suggested when a VoIP connection is established. Examples: G.711ulaw: '0,255,255,255,255' G.711ulaw,G.711alaw: '0,1,255,255,255' G.711ulaw,G.711alaw,G.726: '0,1,2,255,255' G.711ulaw,G.711alaw,G.726,G.729: '0,1,2,3,255' G.711ulaw,G.711alaw,G.726,G.729,G.722: '0,1,2,3,5'

WebUI:Settings - Telephony - Audio - Advanced Settings - Enable Annex B for codec G.729

In the Enable Annex B for codec G.729 field, state whether the transmission of data packets during pauses should be suppressed when using the G.729 codec.

integer:

0=INT 1

1=INT 2

2=INT 3

3=INT 4

4=INT 5

5=INT 6

WebUI:Settings - Telephony - Call Divert - When

Select when an incoming call to the connection should be forwarded: 'When busy', calls are forwarded when the connection is busy. 'On no reply', calls are forwarded if no one accepts the call within several rings. 'Always', calls are forwarded immediately, i.e., no more calls to this connection are signalled on your base station. 'Off', disable call forwarding

WebUI:Settings - Telephony - Call Divert - Call Number

Enter the number to which the calls should be forwarded (maximum 20 characters, 0-9, *, #, R (flash), P (pause))

WebUI:Settings - Telephony - Dialling Plans - Active(checkmark)

Select the Yes/No to enable/disable the corresponding dialling plan. A disabled dialling plan will not take effect until it is re-enabled.

WebUI:Settings - Telephony - Dialling Plans - Phone Number

Enter a phone number for which the dialling plan is to be used (maximum 15 characters, 0-9,*,#,R,P). For each rule, the number must be distinct. If you enter just a few digits (e.g., local area, international or mobile network code), then the rule applies to all phone numbers that begin with these digits.

WebUI:Settings - Telephony - Dialling Plans - Use Area Code(checkmark)

Select the option in the Use Area Code column to precede the corresponding number with the local area code that you have specified under Local Settings.

WebUI:Settings - Telephony - Dialling Plans - Connection

Select the connection via which the number or numbers that start with the specified sequence of digits should be dialled. The list shows all the connections that you have configured for the phone. Select Block from the list if you want to block the number or numbers.

WebUI:Settings - Telephony - Dialling Plans - Comment

You can enter a description of the dialling plan here (maximum 20 characters).

WebUI:Settings - Telephony - Dialling Plans - Code for VoIP line

If you connect your base station to a PABX, you may have to enter an access code for external calls (external prefixes e.g., 0). You can save this access code in the base station. These settings apply to all registered handsets.

WebUI:Settings - Telephony - Network Mailboxes - Call Number

VoIP connections: maximum 32 characters and/or digits (0-9,A-Z,a-z,*,#,R,P,-)

WebUI:Settings - Telephony - Network Mailboxes - Call Number

VoIP connections: maximum 32 characters and/or digits (0-9,A-Z,a-z,*,#,R,P,-)

WebUI:Settings - Telephony - Advanced VoIP settings - Automatic negotiation of DTMF transmission

If you select Yes, for each call, the phone attempts to set the appropriate DTMF signalling type for the codec currently being negotiated. If you select No, you can specify the DTMF signalling type explicitly.

integer:

1=Audio

2=RFC 2833

3=Audio+RFC2833

4=SIP INFO

5=Audio+SIP INFO

6=RFC2833+SIP INFO

7=Audio+RFC2833+SIP INFO

WebUI:Settings - Telephony - Advanced VoIP settings - Send settings of DTMF transmission

Enable Audio or RFC 2833 if DTMF signals are to be transmitted acoustically (in voice packets). Enable SIP Info if DTMF signals are to be transmitted as code. Note: Automatic negotiation of DTMF transmission needs to be set to 'No'

WebUI:Settings - Telephony - Advanced VoIP settings - Use the R key to initiate call transfer

with the SIP Refer method if you choose 'Yes', you can connect the two external callers with each other by pressing the R key. Your connections with the parties are terminated.

WebUI:Settings - Telephony - Advanced VoIP settings - Transfer Call by On-Hook

If you select 'Yes', the external parties are connected when you replace the handset. Your connections with the parties are terminated.

WebUI:Settings - Telephony - Advanced VoIP settings - Find target addr. automatically

If you select 'Yes', the base station will automatically attempt to determine the best protocol. If you select 'No', it will use the protocol defined in Derive target address.

integer:

0=from the SIP URL

1=from the SIP contact header

WebUI:Settings - Telephony - Advanced VoIP settings - Derive target address

from the SIP URL:recommended when the base station is connected to the Internet via a router with NAT.

from the SIP contact header: recommended for 'closed' networks (internal company and business networks).

WebUI:Settings - Telephony - Advanced VoIP settings - Hold on transfer target(For attended transfer)

If you select 'For attended transfer', the first call on your phone's VoIP connection must be held until the consultation call is accepted. Only then can the two callers be connected with each other.

WebUI:Settings - Telephony - Advanced VoIP settings - Hold on transfer target (For unattended transfer)

If you select 'For unattended transfer', the caller must only be placed on hold until you have started the consultation call (dialled the number). You call transfer the call before the second participant registers.

WebUI:Settings - Telephony - Advanced VoIP settings - Use random ports

Select the 'No' to Use random ports if you want the phone to use the ports specified in the SIP port and RTP port fields. Select the 'Yes' option if you want the phone to use any free ports from defined port number ranges instead of fixed ports for SIP port and RTP port.

WebUI:Settings - Telephony - Advanced VoIP settings - Use random ports

Enter the lowest port number in the port number range (numbers between 1024 and 49152). The default port number for SIP signalling is 5060.

WebUI:Settings - Telephony - Advanced VoIP settings - Use random ports

Enter the highest port number in the port number range (numbers between 1024 and 49152). The default port number for SIP is 5076.

WebUI:Settings - Telephony - Advanced VoIP settings - Use random ports

Enter the lowest port number (numbers between 1024 and 55000). The default RTP port is 5004.

WebUI:Settings - Telephony - Advanced VoIP settings - Use random ports

Enter the highest port number (numbers between 1024 and 55000). The default RTP port is 5020.

WebUI:Settings - Messaging - eMail - Display name

Enter a name for the e-mail account in order to identify it on the handset (maximum 32 characters).If you do not enter anything, the first 32 characters of the account name are displayed.

WebUI:Settings - Messaging - eMail - Authentication Name

Enter your username or e-mail account name as agreed with the Internet provider (maximum 74 characters).

WebUI:Settings - Messaging - eMail - Authentication Password

Enter the password agreed with your provider for accessing the POP3/POP3S server (maximum 32 characters; case-sensitive).

WebUI:Settings - Messaging - eMail - POP3 Server port

Enter the communication port used on the POP3/POP3S server (number between 1 and 55000; maximum 5 digits). The default setting is port 110.

WebUI:Settings - Messaging - eMail - eMail advice on handset

Select one or multiple handsets, on which the arrival of new e-mails is displayed. Example: INT1 :'0,255,255,255,255,255'; INT1+INT2:'0,1,255,255,255,255'.

integer:

0=Never

15=Every 15min

30=Every 30min

60=Every 60min

180=Every 3h

360=Every 6h

1440=Once per day

WebUI:Settings - Messaging - eMail - Display name

Specifiying the time interval for the periodical check for new e-mails. Select the time interval from the 'Check for new eMail' list at which your phone should check if new messages have arrived via your POP3/POP3S server. Set '0' to disable the check. Select one of the other values to enable the check for new e-mail messages.

WebUI:Settings - Messaging - MWI Light - Missed calls

For each handset you can individually set on behalf of which type of new messages the LED should flash. The message types are: Missed calls, Missed alarms, eMail, Network Mailboxes.

WebUI:Settings - Messaging - MWI Light - Missed Alarms

For each handset you can individually set on behalf of which type of new messages the LED should flash. The message types are: Missed calls, Missed alarms, eMail, Network Mailboxes.

WebUI:Settings - Messaging - MWI Light - eMail

For each handset you can individually set on behalf of which type of new messages the LED should flash. The message types are: Missed calls, Missed alarms, eMail, Network Mailboxes.

WebUI:Settings - Messaging - MWI Light - Network Mailboxes

For each handset you can individually set on behalf of which type of new messages the LED should flash. The message types are: Missed calls, Missed alarms, eMail, Network Mailboxes.

WebUI:Settings - Management - Date&Time - Automatic adjustment of System Time with Time Server

In the Automatic adjustment of System Time with Time Server field, select 'Yes' to enable synchronisation between the phone and a time server.If you select 'No', the phone will not adopt time settings from a time server.

WebUI:Settings - Management - Date&Time - Time Server

Enter the Internet address or DNS name of the time server from which the time and date settings should be copied (maximum 74 characters, 0-9,a-z,A-Z,-,.). The time server 'europe.pool.ntp.org' is set by default. You can overwrite this setting.

0=(GMT-12:00) International Date Line West; 1=(GMT-11:00) Midway Island, Samoa;

2=(GMT-10:00) Hawaii; 3=(GMT-09:00) Alaska;

4=(GMT-08:00) Pacific Time (US and Canada), Tijuana; 5=(GMT-07:00) Arizona;

6=(GMT-07:00) Chihuahua, La Paz, Mazatlan; 7=(GMT-07:00) Mountain Time (US and Canada);

8=(GMT-06:00) Central America; 9=(GMT-06:00) Central Time (US and Canada);

10=(GMT-06:00) Guadalajara, Mexico City, Monterrey; 11=(GMT-06:00) Saskatchewan;

12=(GMT-05:00) Bogota, Lima, Quito; 13=(GMT-05:00) Eastern Time (US and Canada);

14=(GMT-05:00) Indiana (East); 15=(GMT-04:00) Atlantic Time (Canada);

16=(GMT-04:00) Caracas, La Paz; 17=(GMT-04:00) Santiago;

18=(GMT-03:30) Newfoundland; 19=(GMT-03:00) Brasilia;

20=(GMT-03:00) Buenos Aires, Georgetown; 21=(GMT-03:00) Greenland;

22=(GMT-02:00) Mid-Atlantic; 23=(GMT-01:00) Azores; 24=(GMT-01:00) Cape Verde Is.;

25=(GMT00:00) Casablanca, Monrovia; 26=(GMT00:00) Greenwich Mean Time : Dublin, Edinburgh, Lisbon, London;

27=(GMT+01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna;

75=(GMT+01:00) Namibia; 28=(GMT+01:00) Belgrade, Bratislava, Budapest, Ljubljana, Prague;

29=(GMT+01:00) Brussels, Copenhagen, Madrid, Paris;

30=(GMT+01:00) Sarajevo, Skopje, Warsaw, Zagreb; 31=(GMT+01:00) West Central Africa;

32=(GMT+02:00) Athens, Beirut, Istanbul, Minsk; 76=(GMT+02:00) Jordan, Palestine;

33=(GMT+02:00) Bucharest; 34=(GMT+02:00) Cairo; 35=(GMT+02:00) Harare, Pretoria;

36=(GMT+02:00) Helsinki, Kyiv, Riga, Sofia, Tallinn, Vilnius; 37=(GMT+02:00) Jerusalem;

38=(GMT+03:00) Baghdad; 39=(GMT+03:00) Kuwait, Riyadh;

40=(GMT+03:00) Moscow, St. Petersburg, Volgograd; 41=(GMT+03:00) Nairobi;

42=(GMT+03:30) Tehran; 43=(GMT+04:00) Abu Dhabi, Muscat;

44=(GMT+04:00) Baku, Tbilisi, Yerevan; 45=(GMT+04:30) Kabul;

46=(GMT+05:00) Ekaterinburg; 47=(GMT+05:00) Islamabad, Karachi, Tashkent;

48=(GMT+05:30) Chennai, Kolkata, Mumbai, New Delhi;

49=(GMT+05:45) Kathmandu; 50=(GMT+06:00) Almaty, Novosibirsk;

51=(GMT+06:00) Astana, Dhaka; 52=(GMT+06:00) Sri Jayawardenepura;

53=(GMT+06:30) Rangoon; 54=(GMT+07:00) Bangkok, Hanoi, Jakarta;

55=(GMT+07:00) Krasnoyarsk; 56=(GMT+08:00) Beijing, Chongqing, Hong Kong, Urumqi; 57=(GMT+08:00) Irkutsk, Ulaan Bataar; 58=(GMT+08:00) Kuala Lumpur, Singapore;

59=(GMT+08:00) Perth; 60=(GMT+08:00) Taipei;

61=(GMT+09:00) Osaka, Sapporo, Tokyo; 62=(GMT+09:00) Seoul;

63=(GMT+09:00) Yakutsk; 64=(GMT+09:30) Adelaide;

65=(GMT+09:30) Darwin; 66=(GMT+10:00) Brisbane;

67=(GMT+10:00) Canberra, Melbourne, Sydney;

68=(GMT+10:00) Guam, Port Moresby; 69=(GMT+10:00) Hobart; 70=(GMT+10:00) Vladivostok;

71=(GMT+11:00) Magadan, Solomon Is., New Caledonia;

72=(GMT+12:00) Auckland, Wellington; 73=(GMT+12:00) Fiji, Kamchatka, Marshall Is.; 74=(GMT+13:00) Nuku'alofa;

WebUI:Settings - Management - Date amp;Time - Time Zone

A list of the valid time zones is displayed. Each time zone shows the deviation between local time (not summer time) and Greenwich Mean Time (GMT). Select the appropriate Time Zone for the location of the phone from the list.

WebUI:Settings - Management - Date&Time - Automatically adjust clock for daylight saving changes

Select 'Yes' if you want the time to change automatically to summer time or standard time when summer time begins and ends respectively. Select 'No' if you do not want to change to summer time.

integer:

0=Albania; 1=Argentina; 2=Australia; 3=Austria

4=Bahrain; 5=Belarus; 6=Belgium; 7=Bolivia

8=Bosnia and Herzegovina; 9=Brazil; 10=Bulgaria

11=Canada; 12=Chile; 13=China; 14=Colombia

15=Costa Rica; 16=Croatia; 17=Cyprus

18=Czech Republic; 19=Denmark; 20=Ecuador

21=Egypt; 22=Estonia; 23=Finland; 24=France

25=Germany; 26=Greece; 27=Hong Kong

28=Hungary; 29=Iceland; 30=India; 31=Indonesia

82=Iran; 32=Ireland; 33=Israel; 34=Italy; 35=Japan

36=Jordan; 37=Korea, Republic of; 38=Kuwait

39=Latvia; 40=Lebanon; 41=Liechtenstein

42=Lithuania; 43=Luxembourg; 44=Macedonia

45=Malaysia; 46=Mexico; 81=Montenegro

47=Morocco; 79=Namibia; 48=Netherlands

49=New Zealand; 50=Norway; 51=Pakistan

80=Palestine; 52=Panama; 53=Paraguay

54=Peru; 55=Philippines; 56=Poland; 57=Portugal

58=Puerto=Rico; 59=Romania; 60=Russia

61=Saudi Arabia; 62=Serbia; 63=Singapore

64=Slovakia; 65=Slovenia; 66=South Africa

67=Spain; 68=Sweden; 69=Switzerland

70=Taiwan; 71=Thailand; 72=Turkey

73=United Arab Emirates; 74=United Kingdom

75=United States of America; 76=Uruguay

77=Venezuela; 78=Other Country; 255=undefined

WebUI:Settings - Management - Local Settings - Country

Select the country in which you are using your phone from the list (e. g. Germany). If your country is not included in the country list, select Other Country at the end of the Country list.

integer:

0=International

1=United States of America

2=Switzerland

3=South Africa

4=Austria

5=Czech Republic

6=Spain

7=France

8=United Kingdom

9=Netherlands

10=Poland

11=Russia

12=Germany

13=Italy

14 =Denmark

15 =Finland

16 =Norway

17 =Sweden

WebUI:Settings - Management - Local Settings - Tone Pattern

Tones, e.g. dialling tones, call tones, busy tones or call waiting tones are country-and region-specific. You can choose from various tone groups for your phone. The Tone Selection is automatically assigned according to the country which you selected above. You can change this setting. Select the country or region from the Tone Selection list which should be used for your phone.

WebUI:Management - Miscellaneous - Signal Ethernet Connection and Traffic

If LED signalling is enabled on the base station, the paging key on the front panel of the base station lights up if it is connected to the router (LAN). It flashes if data is being transferred on the LAN connection

WebUI:Management - Firmware update - Data server

Address of data server providing the files needed for profile download, firmware download and provisioning.

Usage of non symbolic:

<I_PHONE_SYSTEM class="integer" value="5"/>

symbolic NVM where custom parameter will be stored: BS_IP_Data.ucI_PHONE_SYSTEM