The following alarms are supported by the handset:

  • Manual Alarm
  • Non Movement Alarm
  • Man Down Alarm
  • Time Alarm
  • Escape Alarm

General values are entered for all alarms. Furthermore, parameters are preconfigured for each alarm type, which can be adapted individually however for the corresponding application.


Use PNG Mode for BGR 139-compliant operation and observe the settings prescribed there.

At least one automatic alarm has to be activated here in addition to the manual alarm.

It is not possible to switch off all alarms in PNG Mode.


General Settings

These values are used in general for all alarm types within an operating mode. 

Procedure:

  1. Select the Additional Features icon in the main menu.
  2. Select Configuration.
  3. Enter the five-position service PIN and confirm with OK.
  4. Select one of the three operating modes.
  5. Select Alarms.
  6. Select General Settings.
  7. Change the values of the following parameters:


ParametersBasic modeAlarm modePNG mode
Alarm number(s) / Alarm DestinationAlarm Destination 1 <empty>--

Alarm Destination 2 <empty>--

Alarm Destination 3 <empty>--
Call retry counter15--
Calling Time30 sec--
Audio ChannelHands-free--


Manual alarm

You can configure all settings here for the manual alarm, in other words for the alarm triggered with the red alarm key.

Depending on how the red alarm key is pressed (SP: Short press, LP: Long press), different alarms are signaled (Alarm/PNG) and different alarm destinations are dialed (Basic).

Procedure:

  1. Select the Additional Features icon in the main menu.
  2. Select Alarm Configuration.
  3. Enter the five-position service PIN and confirm with OK.
  4. Select one of the three operating modes.
  5. Select Alarms.
  6. Select Manual Alarm.
  7. Change the values of the following parameters:

ParametersBasic modeAlarm modePNG mode

Short press Alarm Key

OnOnOn

Long press Alarm Key

OnOnOn
Keypad LockedKey activeKey activeKey active
SP Pre-Alarm Time

0 sec.

<0-300 sec>

0 sec.

<0-300 sec>

0 sec.

<10-90 sec>

SP Pre-Alarm Ringtone

31 Alarm 5

31 Alarm 5

31 Alarm 5

SP Pre-Alarm Volume

50

50

50

SP Alarm Signal

On

On

On

SP Alarm Signal Ringtone31 Alarm 531 Alarm 531 Alarm 5
SP Alarm Signal Volume100100100
LP Pre-Alarm Time

0 sec.

<0-300 sec>

0 sec.

<0-300 sec>

0 sec.

<10-90 sec>

LP Pre-Alarm Ringtone

32 Alarm 6

32 Alarm 6

32 Alarm 6

LP Pre-Alarm Volume

50

50

50

LP Alarm Signal

On

On

On

LP Alarm Signal Ringtone32 Alarm 632 Alarm 632 Alarm 6
LP Alarm Signal Volume100100100


No-Motion Alarm

The No-Motion Alarm can be activated optionally. It is triggered if the sensors identify lack of movement over a defined configurable period of time.


The response time and the pre-alarm time cannot be added, rather the pre-alarm time has to be deducted from the response time. For example, a response time of 90 s and pre-alarm time of 15 s means that the pre-alarm will be triggered after 75 s and the alarm after 90 s.


Procedure:

  1. Select the Additional Features icon in the main menu.
  2. Select Configuration.
  3. Enter the five-position service PIN and confirm with OK.
  4. Select one of the three operating modes.
  5. Select Alarms.
  6. Select No-Motion Alarm.
  7. Change the values of the following parameters:


ParametersBasic modeAlarm modePNG mode
ActivationOnOnOn
Response Time

90 sec.

<10-900 sec>

90 sec.

<10-900 sec>

90 sec.

<10-90 sec>

Pre-alarm Time

15 sec.

<0-300 sec>

15 sec.

<0-300 sec>

15 sec.

<0-30 sec>

Sensitivity levelHighHighHigh


Man Down Alarm

The Man Down Alarm can be activated optionally. It is triggered if the sensors identify undue tilting of the handset over a defined configurable period of time (i.e. deviation from the vertical position).

Procedure:

  1. Select the Additional Features icon in the main menu.
  2. Select Configuration.
  3. Enter the five-position service PIN and confirm with OK.
  4. Select one of the three operating modes.
  5. Select Alarms.
  6. Select Man Down Alarm.
  7. Change the values of the following parameters:


ParametersBasic modeAlarm modePNG mode
ActivationOnOnOn
Response Time

90 sec.

<10-900 sec>

90 sec.

<10-900 sec>

90 sec.

<10-90 sec>

Pre-alarm Time

15 sec.

<0-300 sec>

15 sec.

<0-300 sec>

15 sec.

<0-30 sec>

Sensitivity levelHighHighHigh


Time Alarm

The Time Alarm can be activated optionally. It is triggered if a timed alarm is not acknowledged in time by the user.

Procedure:

  1. Select the Additional Features icon in the main menu.
  2. Select Configuration.
  3. Enter the five-position service PIN and confirm with OK.
  4. Select one of the three operating modes.
  5. Select Alarms.
  6. Select Time Alarm.
  7. Change the values of the following parameters:


ParametersBasic modeAlarm modePNG mode
ActivationOffOffOff
Response Time

15 min.

<1-120 min.>

15 min.

<1-120 min.>

15 min.

<1-15 min.>

Pre-alarm Time

15 sec.

<0-300 sec>

15 sec.

<0-300 sec>

15 sec.

<0-15 sec>


Escape Alarm

The Escape Alarm can be activated optionally. It is triggered if the sensors identify undue violent movement of the handset over a defined configurable period of time.

Procedure:

  1. Select the Additional Features icon in the main menu.
  2. Select Configuration.
  3. Enter the five-position service PIN and confirm with OK.
  4. Select one of the three operating modes.
  5. Select Alarms.
  6. Select Escape Alarm.
  7. Change the values of the following parameters:


ParametersBasic modeAlarm modePNG mode
ActivationOffOffOff
Response Time

30 sec.

<10-900 sec>

30 sec.

<10-900 sec>

30 sec.

<10-90 sec>

Pre-alarm Time

15 sec.

<0-300 sec>

15 sec.

<0-300 sec>

15 sec.

<0-30 sec>

Sensitivity levelHighHighHigh


Alarm Signal

You can define the acoustic signaling of pre-alarms and alarms here. The following signals start quietly and reach their configured maximum value after a short time.

Procedure:

  1. Select the Additional Features icon in the main menu.
  2. Select Configuration.
  3. Enter the five-position service PIN and confirm with OK.
  4. Select one of the three operating modes.
  5. Select Alarms.
  6. Select Alarm Signal.
  7. Select Pre-Alarm or Alarm Signal.
  8. Change the values of the following parameters:


ParametersBasic modeAlarm modePNG mode
Pre-Alarm


  • Warning Signal
OnOnOn
  • Alarm Ringtone
31 Alarm 531 Alarm 531 Alarm 55
  • Volume
505050
  • LED blinking
OffOffOff
Alarm Signal


  • Alarm Signal
OnOnOn
  • Alarm Ringtone
27 Alarm 127 Alarm 127 Alarm 1
  • Volume
100100100
  • LED blinking
OffOffOff
  • No labels